Hard Reset Ea2700

First switch on router. Then, Find the Reset button on the router (Generally back side of the router). Press and hold the Reset button with sensitive material while you power on the router. After that Release the Reset button after 10 to 15 seconds.

1. Hard Reset Linksys Ea2700
2. Factory Reset Ea2700
3. Hard Reset A7000

1. A hard reset should not be confused with a cold boot, also known as a hard boot. Also, this term can be used to describe a factory reset. With a network home router, there is a reset button the back of the router that will reboot the router when pressed. A hard reset is when you press and hold in on.
2. Do a hard reset on router Log into Linksys Web Interface Firmware Upgrade page Upload the known good initial flash E1200 (v1) Trailed Build; Wait 5 minutes to assure flash integrity, then power cycle the E1200 (unplug for 10 seconds). Plug the E1200 back in and wait about 2 minutes until it finishes booting. Do a hard reset, then wait for it to.

How to factory resetSAMSUNG E270L Galaxy Grand? How to wipe all data in SAMSUNG E270L Galaxy Grand? How to bypass screen lock in SAMSUNG E270L Galaxy Grand? How to restore defaults in SAMSUNG E270L Galaxy Grand?

The following tutorial shows all method of master reset SAMSUNG E270L Galaxy Grand. Check out how to accomplish hard reset by hardware keys and Android 4.1 Jelly Bean settings. As a result your SAMSUNG E270L Galaxy Grand will be as new and your Samsung Exynos 4412 core will run faster.

First method:

1. Firstly, switch on the device by pressing the Power button for a couple of seconds.
2. In the next step hold down the Volume Up + Volume Down + Power key.
3. As soon as Recovery Mode appears, release all held keys.
4. From the menu choose 'Wipe Data/Factory Reset' by using Volume buttons to scroll and Power button to select options.
5. Tap 'Yes--delete all user data' to confirm the operation if you are certain you want to clear all your data.
6. Use the Power button to accept option 'reboot system now'.
7. Well done! The hard reset has just been performed.

Check other SAMSUNG device solutions:

From DD-WRT Wiki

Hard Reset Linksys Ea2700

[edit]Hard Reset (aka 30/30/30 reset)

Note: This should only be done on older routers. On newer routers, ex: Asus N66U, this will put them in recovery mode instead.

The following procedure will clear out the NVRAM and set dd-wrt back to default values:

• With the unit powered on, press and hold the reset button on back of unit for 30 seconds
• Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
• Plug the unit back in STILL holding the reset button a final 30 seconds (please note that this step can put Asus devices into recovery mode...see note below!)

This procedure should be done BEFORE and AFTER every firmware upgrade/downgrade.

Do not use configuration restore if you change firmware builds (different svn build numbers).

[NOTE] - For Asus units, the standard 30/30/30 method will reset the router but you will need to use the Restore button followed by a Power cycle. The only exception (so far) is the RT-N16 model, follow the same method as stated above but use the WPS button instead of the Restore button. If all else fails to reset you can also do it by command line (all units). Login to the router via telnet/ssh and issue the command 'erase nvram'. This will reset the nvram partition to defaults for this Make of router.....redhawk

[edit]Hard Reset on ARM and other newer routers

Do not use 30-30-30 hard reset on any ARM router. Reference: Kong

1. Power off the unit.
2. Press and hold on to the WPS button.
3. While holding down the WPS button, power on the unit.
4. Keep holding the WPS button until the power led starts to blink a few times.
5. When the power led starts blinking / flashing, release the WPS button.

[edit]Erasing NVRAM

An alternative method to restore DD-WRT to default settings without using the reset button is via telnet or SSH. This is useful if locked out of the web interface or the reset button is disabled, broken, or 30/30/30 doesn't work. This should not be done on some models, so refer to the device wiki and/or forum device threads.

Using DD-WRT with Telnet (or SSH) for builds after 18 Apr 2018 (35770 and later):

Calling erase nvram will still erase the nvram mtd, but on reboot (or any other action) the nvram is saved to mtd from RAM, so this will not wipe everything unless power is removed right after the erase nvram. However, nvram erase clears the nvram in RAM then then writes to flash, but does not zero out the flash from first to last block. (Reference: Kong's comments)

Builds from 18 Apr 2018 or older (35681 and prior) use:

Alternate direct method, but not recommended and should be used with caution!

Note: The command in Broadcom CFE (bootloader) mode is `nvram erase`

Factory Reset Ea2700

[CAUTION] - This should not be used on some devices. For example, on the Asus WL-500g and Motorola WR850G, the bootloader will not create default values and the device will not boot properly. On a Siemens SE505 V1, the router will no longer be accessible and must be reflashed with stock firmware on IP address 192.168.1.1 (NOT 192.168.2.1 as the installation procedure says)

Hard Reset A7000

[edit]Default password

If the reset is successful, after reboot the GUI will prompt to set a User and Password (except for very old builds).